​KembaraXtra-Computer Terms – blind search:
Blind search is a method of searching for information in memory or on a storage device without any prior knowledge of where the data is located or how it is organized. The system simply checks each possible location until the desired data is found.
Because it does not rely on indexing or ordered data structures, blind search can be slower than more efficient search methods. It is often associated with simple search techniques such as linear searching.

K​embaraXtra-Computer Terms – blink:
To blink in computing means for a display element to flash repeatedly between visible and invisible states. This visual effect is often used to attract the user’s attention to a particular item on the screen.
Elements such as text cursors, insertion points, warning messages, or menu selections may blink to indicate activity or highlight important information. In many graphical user interfaces, the blinking behavior can be adjusted by the user.

​ KembaraXtra-Computer Terms – blink speed:
Blink speed refers to the rate at which a blinking display element alternates between visible and invisible states. This is most commonly associated with the cursor that marks the current insertion point in a text editor or document window.
Many computer systems allow users to adjust the blink speed according to personal preference. A slower or faster blinking cursor can make it easier for users to locate the active typing position on the screen.

​KembaraXtra-Computer Terms – blip:
A blip is a small mark or signal detected optically on a recording medium such as microfilm. These marks are used to assist with counting, indexing, or tracking information within stored records.
Blips allow systems to identify positions or sections within a sequence of recorded data. By detecting these marks, equipment can quickly locate specific portions of stored information.

​KembaraXtra-Computer Terms – bistable:
Bistable describes a system or device that can exist in two stable states. These states are typically represented as on and off or as binary values such as zero and one. Once the system enters one of these states, it remains there until an external action forces it to change.
This property is widely used in digital electronics and computing systems. Bistable devices are essential for storing information and controlling logical operations because they can maintain a stable condition until a triggering signal causes them to switch to the other state.

​KembaraXtra-Computer Terms – bistable circuit:
A bistable circuit is an electronic circuit that has exactly two stable operating states. The circuit does not change between these states on its own; instead, an external signal or trigger must initiate the transition from one state to the other.
Because it can hold one of two conditions, a bistable circuit is capable of storing a single binary digit, or bit, of information. These circuits are commonly used in memory components, digital logic systems, and devices such as flip-flops that form the foundation of many computing processes.

​KembaraXtra-Computer Terms – BISYNC:
BISYNC, short for Binary Synchronous Communications protocol, is a communication standard developed by IBM for transmitting data between computer systems. The protocol allows information to be encoded using either ASCII or EBCDIC character sets and supports messages of varying lengths that are transmitted in units known as frames.
The protocol operates using synchronous transmission, meaning that data elements are separated by precise timing intervals so that the sending and receiving devices remain synchronized. Special control characters are used to indicate the beginning and end of message text, while additional characters are included to verify the accuracy of the transmitted data.

​KembaraXtra-Computer Terms – bit:
A bit, short for binary digit, is the smallest unit of data used in computing and digital communications. It represents a single binary value, either 0 or 1, which can also correspond to logical states such as true or false. In physical hardware, a bit may be represented by two different electrical states, such as high or low voltage, or by magnetic states on storage media like disks.
Although a single bit contains very little meaningful information on its own, groups of bits are used to represent more complex data. For example, eight bits form a byte, which can represent characters such as letters, numbers, or symbols in coding systems like ASCII.

​KembaraXtra-Computer Terms – bit block:
A bit block refers to a rectangular group of pixels in computer graphics that is treated as a single unit. The term originates from the fact that each pixel’s characteristics, such as color or brightness, are represented by bits stored in memory.
Programmers often manipulate these groups of pixels collectively to speed up graphical operations. Techniques such as bit block transfer allow entire sections of an image to be moved, copied, or modified quickly on the display screen.

​KembaraXtra-Computer Terms – bit block transfer:
Bit block transfer is a graphics programming technique used to move or manipulate rectangular blocks of bits stored in memory that represent a portion of an image on the screen. These bits describe pixel attributes such as color and intensity.
By transferring a block of data as a single unit within video memory, computers can display or animate graphics efficiently. This method allows objects like cursors or small images to move across the screen without requiring the entire display to be redrawn, which improves performance in graphical applications.